Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
articles:source_inspections [2022/01/13 18:04] – [Benefits] rrandallarticles:source_inspections [2022/01/14 09:47] (current) – [What are Source Inspections?] rrandall
Line 1: Line 1:
 ===== What are Source Inspections? ===== ===== What are Source Inspections? =====
  
-A “Source Inspection" is different from a “Supplier Audit” (or Product Audit) because it is an “__inspection__” (not an audit). Unlike a Supplier/Product Audit (which follows a product through its entire production process – verifying that requirements have been met). A Source Inspection either takes place at:+A “Source Inspection" is different from a “Supplier Audit” (or Product Audit) because it is an “__inspection__” (not an audit). Unlike a Supplier/Product Audit (which follows a product through its entire production process – verifying that requirements have been met), a Source Inspection either takes place at:
   * the end of the production line (e.g., inspecting a sampling of completed/finished parts/assemblies within a lot/batch or of a single part/assembly representative of the first production lot/batch (i.e., a First Article Inspection))   * the end of the production line (e.g., inspecting a sampling of completed/finished parts/assemblies within a lot/batch or of a single part/assembly representative of the first production lot/batch (i.e., a First Article Inspection))
   * at a specific point in the process (i.e., an "in-process" inspection)   * at a specific point in the process (i.e., an "in-process" inspection)
Line 10: Line 10:
   * the raw material certifications (e.g., Certificate of Analysis, Material Test Reports) supports that the material used complies with the requirements for the finished product.    * the raw material certifications (e.g., Certificate of Analysis, Material Test Reports) supports that the material used complies with the requirements for the finished product. 
   * that any “Special Processes” are supported by certificates from the processing operation (whether in-house or outsourced). The Aerospace industry usually requires those special processes to be [[https://p-r-i.org/nadcap/accreditation/|Nadcap accredited]].   * that any “Special Processes” are supported by certificates from the processing operation (whether in-house or outsourced). The Aerospace industry usually requires those special processes to be [[https://p-r-i.org/nadcap/accreditation/|Nadcap accredited]].
 +
 +While a "Source Inspection" typically involves the Inspector personally performing the inspection activities, there are valid reasons for why an Inspector may instead, choose to "witness" a supplier's employee(s) performing the inspection activities. The most common reason for this is that the Inspector does not have the portable measuring instruments necessary for performing the inspection. While the Customer may require the Supplier to provide the necessary measuring instrumentation, this can introduce a liability (e.g., the Inspector inadvertently damaging the supplier's measuring instrumentation). Witnessing, rather than performing the inspection, greatly mitigates this liability. 
 +
 +Witnessing an inspection activity, rather than performing it, also provides some benefits. For example, witnessing the inspection(s) allows the "Source Inspector" to verify that the supplier's employee(s), whether production personnel or quality control inspectors - possess the knowledge, skills, and ability (KSA) to:
 +  * Read and understand applicable drawings/specifications (e.g., GD&T - Geometric Dimensioning and Tolerancing)
 +  * Verify correct raw material was used (e.g., through associated Material Test Reports, Chemical Analysis Reports)
 +  * Verify correct welding/brazing filler material was used (e.g., through associated Certified Material Test Reports)
 +  * Verify correct soldering material (solder wire, solder paste, solder bar) was used (e.g., lead-free solder vs. lead solder)
 +  * Availability and proper use of measuring instruments required for the inspection
 +  * Maintain an acceptable accuracy ratio (between the measuring instrument accuracy and the tolerance(s) being measured)
 +  * Verify consistency of any visual inspections with the specifications
 +  * Verify proper understanding and use of representative standards (e.g., visual inspections)
 + 
  
 === Sampling === === Sampling ===